Residential range

StickerProMaxx 04: the automatic extinguisher for 4-module enclosures

Stuck to the ceiling of a 4-module electrical enclosure, it keeps constant watch and puts out a fire on its own within seconds, with no power, no pressure and no maintenance.

  • Designed for 4-module enclosures, single row only
  • Up to 4 breakers, enclosure of 30 liters max.
  • Installs in 30 seconds, no wiring
StickerProMaxx 04: compact automatic aerosol extinguisher for small electrical enclosures

170 °C

activation threshold

2–4 s

activation

30 L

or 4 breakers

5 years

warranty

StickerProMaxx 04 installed at the top of a small 4-breaker electrical enclosure (Residential range)

Which enclosure is it for?

A 4-module enclosure, and nothing more

The StickerProMaxx 04 is the smallest model in the range: it protects only a 4-module enclosure, i.e. 4 breakers on a single row. Its detection loop is short: it covers those 4 modules, no more.

It’s the typical case of small surface-mounted enclosures that feed a single circuit, often installed away from the main panel, where nobody looks.

Does your enclosure have more than 4 modules? A pool control box or a DC/AC solar box requires at least a StickerProMaxx 08. Choose the model based on the width to cover: 08 (13 cm detection), 12 (23 cm) or 18 (33 cm).

Is it the right model?

The 04 covers a 4-module enclosure from end to end

The golden rule: the device must cover the full width of the hazard. The StickerProMaxx 04 is made for a single-row, 4-module enclosure.

Example: an enclosure with more than 4 modules cannot be effectively protected by the 04. Beyond 4 modules or on several rows, move up to the StickerProMaxx 08, 12 or 18.

The StickerProMaxx 04 is right if…

Enclosure4 modules, single row
Breakers4 maximum
Enclosure volume30 liters maximum
Mounting height20 cm (8 in) max. from the bottom of the enclosure
Detection1 heat-sensitive detection loop
Enclosure ventilation0 to 2% (closed enclosure)
How it works in 3 steps: heat detection, fast activation, extinguishing

How it works

It detects, it activates, it extinguishes

  • Detection. The heat-sensitive loop reacts on contact with the flame, at 170 °C ± 10 °C (338 °F ± 18 °F).
  • Activation. Within 2 to 4 seconds, with no electricity and no human intervention.
  • Extinguishing. A condensed aerosol of potassium and strontium particles fills the enclosure and stops combustion within 6 to 12 seconds.

No pressurized cylinder, no piping, no battery: the generator stays inert until the day it is needed.

Installation

30 seconds to install, no wiring

Electrical safety. Switch off the power before any work. The supply side of the main breaker, solar panels and batteries may remain live. If in doubt, call an electrician.

  1. Switch off the power at the breaker or main disconnect.
  2. Open the enclosure : remove the cover or front panel.
  3. Clean the mounting surface, preferably with isopropyl alcohol.
  4. Stick it to the ceiling of the enclosure, diffuser facing down, directly above the breakers, no more than 20 cm from the bottom. Press for 3 to 4 seconds (or fix with two screws).
  5. Check that the detection loop is clear and positioned above the area to protect, and that nothing blocks the diffuser.
  6. Close up, switch the power back on and write the installation date on the warranty label.
Correct installation: the detection cable must cover the full width above the breakers

Ceiling mounting only, directly above the area to protect. Avoid any direct heat source.

Why condensed aerosol

Protection you install and forget

No pressure, no maintenance

No hydrostatic testing, no refills: 6-year service life, replace after 5 years.

Made for electrical fires

Non-conductive aerosol, effective on class E (electrical) fires, residue under 1 g, non-corrosive and non-toxic.

Compact and eco-friendly

67 mm long and 12.8 g, 100% recyclable housing, zero impact on the ozone layer and climate (ODP 0, GWP 0).

Residential range

The most compact in the Residential range

The wider the enclosure, the wider the detection must be: choose the detection width first, then the volume.

ModelBreakersDetectionRowsMax. mounting height
StickerProMaxx 044 (4-module enclosure)built-in loop · 5 cm120 cm
StickerProMaxx 08up to 813 cm of cableup to 465 cm
StickerProMaxx 12up to 1223 cm of cableup to 465 cm
StickerProMaxx 18up to 1833 cm of cableup to 465 cm
Residential range: StickerProMaxx 04, 08, 12 and 18 depending on the number of breakers

Compliance and documents

EU type-examination passed, patented, designed and assembled in France

Aerosol generator, category P1 pyrotechnic firefighting device under Directive 2013/29/EU. EU type-examination (Module B) passed with notified body No. 0163 (LOM). Composition protected by a European patent. Designed and assembled in Toulouges, France.

StickerProMaxx generator EU type-examination under Directive 2013/29/EU

Frequently asked questions

Your questions about the StickerProMaxx 04

Can I install it myself?

Yes. The StickerProMaxx 04 mounts inside the enclosure in 30 seconds, with no electrical wiring at all. Switch off the power before opening the enclosure; if in doubt, call an electrician.

My enclosure has more than 4 modules: is this the right model?

No. The StickerProMaxx 04 is only for 4-module enclosures: its detection doesn’t cover a longer row. A pool or solar box, for example, requires at least a StickerProMaxx 08. Choose a StickerProMaxx 08, 12 or 18, whose detection cable covers 13, 23 or 33 cm.

Does it need maintenance?

No: it is unpressurized and maintenance-free. A simple monthly visual check is enough (housing secure, diffuser clear, detection loop intact), and you replace it after 5 years.

What happens when it activates?

The flame triggers the detection loop at 170 °C: within 2 to 4 seconds, the generator releases a condensed aerosol that puts out the fire inside the enclosure within 6 to 12 seconds. Then: wait, switch off the power, air out the room, clean the residue (under 1 g, non-corrosive) and replace the device.

Does the aerosol damage electrical equipment?

No. The aerosol is non-conductive and its residue is minimal and non-corrosive: it tackles an electrical (class E) fire without cutting off or damaging nearby equipment.

Does it replace a fire extinguisher?

No. It automatically protects the inside of a closed enclosure. It doesn’t replace a portable extinguisher for a fire that has spread to the room, or a fire safety system where one is required.

Protect your 4-module enclosure today

Ships within 2 business days from Toulouges, France · delivery to France, the European Union, Switzerland, Norway and the United Kingdom · 5-year warranty.