Solution — home

Protect your home electrical panel

A connection working loose, a worn breaker, an overload: electrical fires often start inside the panel, door closed, without anyone seeing. A StickerProMaxx stuck to the ceiling of the panel puts it out on its own within seconds.

  • Panels from 4 modules up to 4 rows of 18
  • No wiring, installs in 30 seconds
  • Works even with the power off
  • Coming soon
StickerProMaxx Residential range: aerosol generator installed in a home electrical panel

170 °C

activation threshold

0

pressure, wiring or maintenance

5 years

warranty and service life

30 s

to install

By the numbers

What an electrical fire at home costs

A home fire in France costs over €14,000 on average, and in 2025 fire became the leading cost for insurers. Yet most older installations have at least one defect.

Over €14,000: average cost of a home fire claim in France (France Assureurs 2025)
2025: fire becomes the #1 cost in French home insurance payouts (28.7%)
82.6% of electrical installations over 15 years old have at least one defect (ONSE)

The risk

The panel, a frequent starting point

Between 20 and 35% of home fires are electrical in origin, and more than 8 out of 10 installations over 15 years old have at least one defect (ONSE). The panel concentrates the connections: that’s where overheating sets in silently. A smoke detector warns you once smoke comes out; the StickerProMaxx acts before that, inside the panel.

Good practice: smoke detector in the home + StickerProMaxx in the panel + fire extinguisher within reach.

24-module electrical panel protected by StickerProMaxx in a garage

Which model?

Count the modules on the fullest row

ModelCapacityDetectionMax. volumeMax. mounting heightPrice incl. VAT
StickerProMaxx 044 modules, 1 rowbuilt-in loop · 5 cm30 L20 cmComing soonBuy
StickerProMaxx 088 modules per row, up to 4 rows13 cm30 L65 cmComing soonBuy
StickerProMaxx 1212 modules per row, up to 4 rows23 cm30 L65 cmComing soonBuy
StickerProMaxx 1818 modules per row, up to 4 rows33 cm30 L65 cmComing soonBuy
StickerProMaxx 50Mx4 rows of 13 modules135 cm, serpentine50 L65 cmComing soonBuy

The number of modules isn’t an absolute limit: a panel is suitable as soon as the volume, width, height and cable are right; a cable extension lets you cover a wider width.

Installation

Positioning the generator correctly

  1. Switch off the power at the main breaker or disconnect, then open the enclosure.
  2. Clean the mounting surface with isopropyl alcohol.
  3. Mount it on the ceiling of the enclosure, diffuser facing down, directly above the area to protect (double-sided adhesive pressed for 3 to 4 seconds, or two screws).
  4. Lay out the detection cable above the entire fullest row, without tight bends; with several well-filled rows, choose the 50Mx and run the cable above each one.
  5. Close up and switch the power back on, then write the installation date on the warranty label.

Frequently asked questions

My panel has 2 rows of 13 modules: which one should I get?

A StickerProMaxx 18 (up to 18 modules per row, 4 rows, 30 L). For detection on every row, the 50Mx.

What if the panel is in a closet?

The generator goes inside the panel itself, with the door or cover closed: it’s the panel’s closed volume that is protected.

Does my insurance require it?

It’s not mandatory. Proof (EU declaration of conformity, data sheet) is available if your insurer asks for it.

Find your model in 30 seconds

The selection guide gives you the right model based on your modules or your volume.